[luau] Road Runner
Mark Kellman
mark_kellman at hotmail.com
Sun Mar 24 09:44:52 PST 2002
Whoops, sorry about the earlier message. Just got this one. God, I feel
like an idiot more now than five minutes ago.
>From: Ray Strode <halfline at hawaii.rr.com>
>Reply-To: luau at videl.ics.hawaii.edu
>To: luau at videl.ics.hawaii.edu
>Subject: Re: [luau] Road Runner
>Date: Sun, 24 Mar 2002 01:50:43 -1000
>
>>
>>
>>>If this is what comes up I don't see how netstat -r could have had
>>>what it had. what does /sbin/ifconfig -a show?
>>>You don't have to type the whole thing. Just tell me if eth0 is there.
>>
>>Output: eth0 is not there
>
>
>Okay that means that the ethernet card's driver module isn't loaded.
>
>>For fun, I ran this command. I received the following output:
>>/etc/sysconfig/network-scripts/ifup-post: ifcfg-eth0: No such file or
>>directory
>
>okay you should have that file..type this:
>
>echo 'DEVICE="eth0"' > /etc/sysconfig/network-scripts/ifcfg-eth0
>echo 'ONBOOT="no"' >> /etc/sysconfig/network-scripts/ifcfg-eth0
>echo 'BOOTPROTO="dhcp"' >>/etc/sysconfig/network-scripts/ifcfg-eth0
>
>>After typing /sbin/ifconfig/ eth0 appears!!!!
>
>Okay, what's happened is when you called dhcpcd the kernel module
>autoloader loaded your ethernet card's driver module.
>
>At this point you can type /sbin/lsmod and that will show you the name
>of the module. In the future if it doesn' load, then you can type
>/sbin/modprobe [modulename]
>to load manually.
>
>>Then I typed the command /sbin/dhcpcd eth0 and received the output:
>>**** /sbin/dhcpcd: already running
>>**** /sbin/dhcpcd: if not then delete /var/run/dhcpcd-eth0.pid file
>
>Yes, that's because you started it a second ago.
>
>>What the hell is going on?! Now, typing /sbin/ifconfig -a outputs the
>>eth0 information:
>>
>It's because the kernel loaded the netcard driver when dhcpcd tried to
>use it.
>
>>eth0 Link encap:Ethernet HWaddr 00:C0:9F:06:5A:91
>> inet addr:66.91.114.64 Bcast:255.255.255.255 Mask:255.255.248.0
>> UP BROADCAST NOTRAILERS RUNNING MTU:1500 Metric:1
>> RX packets:812 errors:557 dropped:557 overruns:0 frame:0
>> TX packets:6 errors:0 dropped:0 overruns:0 frame:0
>> collisions:0
>> RX bytes:53514 (52.2 Kb) TX bytes:3034 (2.9 Kb)
>
>Note you have an IP address (66.91.114.64). Very good sign.
>
>>The output is: /sbin/dhcpcd [its in green?]
>
>green means it's a file that you can run (it's a program)
>
>>After typing resolv.conf at[root at localhost markk] & at [root at localhost
>>etc], the output I receive is: bash: resolv.conf: command not found
>
>resolv.conf is located in /etc and you were in /home/markk so it
>couldn't find it. But you don't want to type resolve.conf at the prompt
>anyway. It's not a program. You can view it using cat
>
>cat /etc/resolv.conf
>
>Now that you've reached this point could you try pinging those IP
>addresses mentioned in past mails. I think you won't get the same error
>messages now.
>
>Also, just for the fun of it type
>/etc/init.d/network start
>
>and tell me if you instantly get internet access upon doing that :-)
>
>--Ray
>
>
>_______________________________________________
>LUAU mailing list
>LUAU at videl.ics.hawaii.edu
>http://videl.ics.hawaii.edu/mailman/listinfo/luau
_________________________________________________________________
Chat with friends online, try MSN Messenger: http://messenger.msn.com
More information about the LUAU
mailing list